EH11A VOLTAGE REGULATOR PDF
eh11a regulator datasheet, cross reference, circuit and application notes in pdf EH11A SOT eh14a regulator eh16a regulator voltage regulator sot Cheap Voltage Regulators/Stabilizers, Buy Directly from China Suppliers:EH11A H11A AZH-ADJ Enjoy ✓Free Shipping Worldwide! ✓Limited Time Sale. Cheap spot cartoon, Buy Quality regulator filter directly from China spot batteries Suppliers: EH11A AZH – ADJTRE1 adjustable power supply voltage.
|Published (Last):||4 September 2015|
|PDF File Size:||10.94 Mb|
|ePub File Size:||18.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
Being that a voltage regulator passes voltagw a regulated output voltage, the only test we must do to check a voltage regulator is a voltage test. We should now read a voltage at or about the rated voltage that the regulator is designed for.
AZ1117H-ADJTRE1 AZ1117H AZ1117 EH11A SOT223
The ground pin is pin 2. Below is the pinout of the LM voltage regulator: If volhage read at the input pin the voltage which we feed into the regulator ey11a read at the output pin the output voltage which the regulator is rated for, then we know that the voltage regulator is good.
If we read a higher voltage, then the voltage regulator is receiving sufficient voltage to regulate down. How To Test a Voltage Regulator A voltage regulator is a device that takes in an input voltage and regulates it down to the voltage that it is rated for.
How to Test a Voltage Regulator
All a user must do is calculate the output that the regulator should output and perform the same test as is shown above to see whether it is good or defective. Measuring the Input Voltage When testing the voltage of a voltage regulator, we first check the voltage from the input pin to ground. A voltage regulator is a device that takes in an input voltage and regulates it down to the voltage that it is rated for. The DC voltage setting is the setting of the multimeter that has the following symbol or sign.
So we’ll now go through specifically how to test a voltage regulator.
EH11A H11A AZ1117H-ADJ
To measure the output voltage, we place the same multimeter set in the DC voltage setting and now place the positive probe of the multimeter on the output pin of the regulator and the negative probe regupator the ground pin of the regulator. And the regulated output voltage comes out from pin 3 Output.
If we do not, then the voltage regulator is defective, as it does not do the job it was designed for, which is output a regulated voltage. An adjustable regulator can be tested in the same way.
We check the voltage input into the voltage regulator and the voltage output from the regulator. We take the probes of the multimeter and place the positive probe normally the red probe on the input pin of the voltage regulator and the negative probe normally black probe on the ground pin.
The LM is a vpltage regulator is rated to output 5 volts, so we should read this output.
eh11a regulator datasheet & applicatoin notes – Datasheet Archive
If the regulator is rated to output 5 volts, then we should read a voltage very near 5 volts coming out from its output. Unlike fixed voltage regulators, adjustable regulators can be regulated to output adjustable voltages.
Measuring the Output Voltage Now that this step is complete, we now read the output voltage. If the multimeter does read a rrgulator near its rated output voltage, the voltage regulator is functional and is good. The input voltage that needs to be regulated down goes into pin 1 Input. The voltage that we should read should be higher than the voltage the regulator is rated to output. This is normally volts higher.
If we don’t read the correct voltages, then more than likely it is a defective regulator. If the regulator eh1a receiving sufficient voltage, of course it will not be able to output its rated regulated voltage. To test the voltage going into the voltage regulator, we take a multimeter and place it in the DC voltage setting.
Before we get into how to read the voltages with a multimeter, first we’ll go over the pinout of a voltage regulator, so that you’ll know which pins to read voltages from.
This is why we do this test. This is to make sure that voltage is, in fact, being supplied to the regulator. As an example, we’ll use volfage popular voltage regulator, the LM